IPMI
Jump to navigation
Jump to search
Useful IPMI commands on SuperMicro AOC-IPMI20 for Serial-Over-LAN Console
SuperMicro ipmitool
# service ipmi stop
SuperMicro Configuration Tool Began to work
# ./ipmicfg-linux.x86_64.static -m
IP=192.168.1.21 MAC=00:30:48:56:A8:14
# ./ipmicfg-linux.x86_64.static -k
Net Mask=255.255.255.0
# ./ipmicfg-linux.x86_64.static -dhcp
DHCP is currently disabled.
# ./ipmicfg-linux.x86_64.static -g
IP=192.168.1.1
# ./ipmicfg-linux.x86_64.static -ver
Firmware Revision: 02.05
# ./ipmicfg-linux.x86_64.static -vlan
VLAN feature is not supported by this firmware.
- https://twiki.cern.ch/twiki/bin/view/FIOgroup/IpmiRefSolSetup
- http://wiki.alteeve.com/index.php/IPMI
Common ipmitool commands
# ipmitool -l open shell
# ipmitool -l open mc reset cold
# ipmitool -I open lan print
# ipmitool -l open session info all
Faster SOL
- IPMIv2 only uses CTS/RTS (RTS/CTS);
# ipmitool -l open sol info 1
sol set character-accumulate-level 1
sol set character-send-threshold 220
sol set retry-count 0
sol set retry-interval 0
sol set non-volatile-bit-rate 115.2
sol set volatile-bit-rate 115.2
Remote IPMI shell
# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN shell
# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate
# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN chassis power reset
rmcp_ping
# rmcp_ping
# rmcp_ping 192.168.1.21
Fedora ??12?? grub.conf
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE: You have a /boot partition. This means that
# all kernel and initrd paths are relative to /boot/, eg.
# root (hd0,0)
# kernel /vmlinuz-version ro root=/dev/VolGroup00/LogVol00
# initrd /initrd-version.img
#boot=/dev/sda
# Redirect grub output to serial console, which is on COM Port 2
serial --unit=1 --speed=19200 --word=8 --parity=no --stop=1
terminal --timeout=10 serial console
default=0
timeout=10
# making IPMI friendly
#splashimage=(hd0,0)/grub/splash.xpm.gz
#hiddenmenu
title CentOS (2.6.18-92.1.22.el5)
root (hd0,0)
kernel /vmlinuz-2.6.18-92.1.22.el5 ro root=/dev/VolGroup00/LogVol00 console=tty0 console=ttyS1,19200n8
initrd /initrd-2.6.18-92.1.22.el5.img
title "My bios update"
kernel /memdisk
initrd /fwdisk.img floppy
Fedora 14 grub.conf
- Set higher buadrate
# cat /etc/grub.conf
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE: You have a /boot partition. This means that
# all kernel and initrd paths are relative to /boot/, eg.
# root (hd0,0)
# kernel /vmlinuz-version ro root=/dev/mapper/vg_drewserv-lv_root
# initrd /initrd-[generic-]version.img
#boot=/dev/sda
serial --unit=1 --speed=115200
terminal --timeout=5 serial console
default=5
timeout=10
#splashimage=(hd0,0)/grub/splash.xpm.gz
#hiddenmenu
title Fedora (2.6.35.11-83.fc14.x86_64)
root (hd0,0)
kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM console=tty0 console=ttyS1,115200
initrd /initramfs-2.6.35.11-83.fc14.x86_64.img
Fedora14 grub.conf orig
grub.conf
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE: You have a /boot partition. This means that
# all kernel and initrd paths are relative to /boot/, eg.
# root (hd0,0)
# kernel /vmlinuz-version ro root=/dev/mapper/vg_drewserv-lv_root
# initrd /initrd-[generic-]version.img
#boot=/dev/sda
serial --unit=1 --speed=19200
terminal --timeout=5 serial console
default=5
timeout=5
#splashimage=(hd0,0)/grub/splash.xpm.gz
#hiddenmenu
title Fedora (2.6.35.11-83.fc14.x86_64)
root (hd0,0)
kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet console=ttyS1,19200
initrd /initramfs-2.6.35.11-83.fc14.x86_64.img
Using the Serial BIOS
- http://buttersideup.com/docs/howto/IPMI_on_Debian.html
- The serial BIOS interface is a bit brain damaged in that it does not recognise the "F11", and "F12" key escape codes that most terminal programs send, instead you can send "Esc-!", and "Esc-@" (yes very logical, as long as the '@' key is normally typed using 'Shift-2' - as on US keyboards, not miles away from the '2' key, as on many non-US keyboards). These escapes from HP, and Dell serial BIOS' may or may not be useful:
Defined As F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
Keyboard Entry <ESC>1 <ESC>2 <ESC>3 <ESC>4 <ESC>5 <ESC>6 <ESC>7 <ESC>8 <ESC>9 <ESC>0 <ESC>! <ESC>@
Defined As Home End Insert Delete PageUp PageDn
Keyboard Entry <ESC>h <ESC>k <ESC>+ <ESC>- <ESC>? <ESC>/
Use the <ESC><Ctrl><M> key sequence for <Ctrl><M>
Use the <ESC><Ctrl><H> key sequence for <Ctrl><H>
Use the <ESC><Ctrl><I> key sequence for <Ctrl><I>
Use the <ESC><Ctrl><J> key sequence for <Ctrl><J>
Use the <ESC><X><X> key sequence for <Alt><x>, where x is any letter key, and X is the upper case of that key
Fedora 13
- Set console=ttyS1,19200n8 last for udev to automatically configure serial console on boot.
Sample Boot
drew@drew-desktop:~$ ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate
Password:
[SOL Session operational. Use ~? for help]
[root@drewserv ~]# shutdown -r now
Broadcast message from [email protected]
(/dev/ttyS1) at 23:10 ...
The system is going down for reboot NOW!
[root@drewserv ~]# Shutting down smartd: [ OK ]
Shutting down Avahi daemon: [ OK ]
Stopping fail2ban: [ OK ]
Stopping sshd: [ OK ]
Shutting down sm-client: [ OK ]
Shutting down sendmail: [ OK ]
Shutting down SMB services: [ OK ]
Stopping crond: [ OK ]
Shutting down NFS mountd: [ OK ]
Shutting down NFS daemon: [ OK ]
[ 150.330672] nfsd: last server has exited, flushing export cache
Shutting down NFS services: [ OK ]
Stopping HAL daemon: [ OK ]
Stopping ipmi drivers: [ OK ]
Stopping lm_sensors: [ OK ]
Shutting down ntpd: [ OK ]
Stopping UPS monitor: [ OK ]
Stopping upsd: [ OK ]
Shutting down UPS driver controller: [ OK ]
Killing mdmonitor: [ OK ]
Stopping system message bus: [ OK ]
Stopping rpcbind: [ OK ]
Stopping auditd: [ 151.494041] type=1305 audit(1302671414.945:21): audit_pid=0 old=1132 auid=4294967295 ses=4294967295 subj=system_u:system_r:auditd_t:s0 res=1
[ OK ]
Shutting down interface eth1: [ OK ]
Shutting down loopback interface: [ OK ]
ip6tables: Flushing firewall rules: [ OK ]
ip6tables: Setting chains to policy ACCEPT: filter [ OK ]
ip6tables: Unloading modules: [ OK ]
iptables: Flushing firewall rules: [ OK ]
iptables: Setting chains to policy ACCEPT: filter [ OK ]
iptables: Unloading modules: [ OK ]
Stopping monitoring for VG vg_drewserv: 3 logical volume(s) in volume group "vg_drewserv" unmonitored
[ OK ]
Stopping monitoring for VG vgraid5: 1 logical volume(s) in volume group "vgraid5" unmonitored
[ OK ]
Sending all processes the TERM signal... [ OK ]
Sending all processes the KILL signal... [ OK ]
Saving random seed: [ OK ]
Syncing hardware clock to system time [ 156.048033] type=1111 audit(1302671419.499:22): user pid=2435 uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:hwclock_t:s0 msg='changing system time: exe="/sbin/hwclock" hostname=? addr=? terminal=? res=success'
[ OK ]
Turning off swap: [ OK ]
Unmounting pipe file systems: [ OK ]
Unmounting file systems: [ OK ]
init: Re-executing /sbin/init
[ 156.385328] EXT4-fs (dm-0): re-mounted. Opts: (null)
Please stand by while rebooting the system...
[ 156.599482] type=1128 audit(1302671420.051:23): user pid=1789 uid=0 auid=4294967295 ses=4294967295 subj=system_u:system_r:initrc_t:s0 msg='init: exe="/lib/upstart/reboot" hostname=? addr=? terminal=console res=success'
[ 156.619403] md: stopping all md devices.
[ 157.624224] sd 3:0:1:0: [sde] Synchronizing SCSI cache
[ 157.629729] sd 3:0:0:0: [sdd] Synchronizing SCSI cache
[ 157.635251] sd 2:0:1:0: [sdc] Synchronizing SCSI cache
[ 157.640734] sd 2:0:0:0: [sdb] Synchronizing SCSI cache
[ 157.646204] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 157.652113] e1000e 0000:0e:00.0: PCI INT A disabled
[ 157.657305] e1000e 0000:0d:00.0: PCI INT A disabled
[ 157.662388] Restarting system.
[ 157.665531] machine restart
Phoenix cME(tm) TrustedCore(tm) Server
Copyright 1985-2004 Phoenix Technologies Ltd.
All Rights Reserved
Supermicro PDSMi/PDSMA/PDSMi+/PDSMA+ BIOS Rev 1.3
CPU = 1 Processors Detected, Cores per Processor = 2
Intel(R) Pentium(R) D CPU 3.00GHz
FSB at 800MHz
Intel(R) Extended Memory 64 Technology.
DRAM Type : DDR2-667
2047M System RAM Passed
1024K Cache SRAM Passed
System BIOS shadowed
Video BIOS shadowed
GNU GRUB version 0.97 (632K lower / 2094976K upper memory)
+-------------------------------------------------------------------------+
| Fedora (2.6.35.11-83.fc14.x86_64) Error sending SOL data: FAIL |
SOL session closed by BMC |
drew@drew-desktop:~$ e |
e: command not found |
drew@drew-desktop:~$ clear |
| |
| |
| |
| |
| |
| |
+-------------------------------------------------------------------------+
Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, 'e' to edit the
commands before booting, 'a' to modify the kernel arguments
before booting, or 'c' for a command-line.
The highlighted entry will be booted automatically in 3 seconds.
drew@drew-desktop:~$ ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate
Password:
[SOL Session operational. Use ~? for help]
�
Phoenix cME(tm) TrustedCore(tm) Server
Copyright 1985-2004 Phoenix Technologies Ltd.
All Rights Reserved
Supermicro PDSMi/PDSMA/PDSMi+/PDSMA+ BIOS Rev 1.3
CPU = 1 Processors Detected, Cores per Processor = 2
Intel(R) Pentium(R) D CPU 3.00GHz
FSB at 800MHz
Intel(R) Extended Memory 64 Technology.
DRAM Type : DDR2-667
2047M System RAM Passed
1024K Cache SRAM Passed
System BIOS shadowed
Video BIOS shadowed
Fixed Disk 1: WDC WD5000AAKS-00A7B0
Fixed Disk 2: WDC WD5000AAKS-22A7B0
Fixed Disk 3: WDC WD5000AAKS-00A7B2
Fixed Disk 4: WDC WD5000AAKS-22A7B0
GNU GRUB version 0.97 (632K lower / 2094976K upper memory)
[ Minimal BASH-like line editing is supported. For the first word, TAB
lists possible command completions. Anywhere else TAB lists the possible
completions of a device/filename. ESC at any time exits.]
grub> help
background RRGGBB blocklist FILE
boot cat FILE
chainloader [--force] FILE clear
color NORMAL [HIGHLIGHT] configfile FILE
displayapm displaymem
find FILENAME foreground RRGGBB
geometry DRIVE [CYLINDER HEAD SECTOR [ halt [--no-apm]
help [--all] [PATTERN ...] hide PARTITION
initrd FILE [ARG ...] kernel [--no-mem-option] [--type=TYPE]
makeactive map TO_DRIVE FROM_DRIVE
md5crypt module FILE [ARG ...]
modulenounzip FILE [ARG ...] pager [FLAG]
partnew PART TYPE START LEN parttype PART TYPE
reboot root [DEVICE [HDBIAS]]
rootnoverify [DEVICE [HDBIAS]] serial [--unit=UNIT] [--port=PORT] [--
setkey [TO_KEY FROM_KEY] setup [--prefix=DIR] [--stage2=STAGE2_
grub will attempt to avoid printing an splashimage FILE
terminal [--dumb] [--no-echo] [--no-ed terminfo [--name=NAME --cursor-address
testvbe MODE unhide PARTITION
uppermem KBYTES vbeprobe [MODE]
grub> reboot
Phoenix cME(tm) TrustedCore(tm) Server
Copyright 1985-2004 Phoenix Technologies Ltd.
All Rights Reserved
Supermicro PDSMi/PDSMA/PDSMi+/PDSMA+ BIOS Rev 1.3
CPU = 1 Processors Detected, Cores per Processor = 2
Intel(R) Pentium(R) D CPU 3.00GHz
FSB at 800MHz
Intel(R) Extended Memory 64 Technology.
DRAM Type : DDR2-667
2047M System RAM Passed
1024K Cache SRAM Passed
System BIOS shadowed
Video BIOS shadowed
Entering SETUP ...
Phoenix cME(tm) TrustedCore(tm) Server
Copyright 1985-2004 Phoenix Technologies Ltd.
All Rights Reserved
Supermicro PDSMi/PDSMA/PDSMi+/PDSMA+ BIOS Rev 1.3
CPU = 1 Processors Detected, Cores per Processor = 2
Intel(R) Pentium(R) D CPU 3.00GHz
FSB at 800MHz
Intel(R) Extended Memory 64 Technology.
DRAM Type : DDR2-667
2047M System RAM Passed
1024K Cache SRAM Passed
System BIOS shadowed
Video BIOS shadowed
Fixed Disk 0: HDT722525DLA380
Fixed Disk 1: WDC WD5000AAKS-00A7B0
Fixed Disk 2: WDC WD5000AAKS-22A7B0
Fixed Disk 3: WDC WD5000AAKS-00A7B2
Fixed Disk 4: WDC WD5000AAKS-22A7B0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.35.11-83.fc14.x86_64 ([email protected]) (gcc version 4.5.1 20100924 (Red Hat 4.5.1-4) (GCC) ) #1 SMP Mon Feb 7 07:06:44 UTC 2011
[ 0.000000] Command line: ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM console=tty0 console=ttyS1,115200
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e000 (usable)
[ 0.000000] BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000ca000 - 00000000000cc000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
[ 0.000000] BIOS-e820: 000000007fee0000 - 000000007fee9000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007fee9000 - 000000007ff00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] No AGP bridge found
[ 0.000000] last_pfn = 0x7fee0 max_arch_pfn = 0x400000000
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] total RAM covered: 2047M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 2M num_reg: 2 lose cover RAM: 0G
[ 0.000000] found SMP MP-table at [ffff8800000f5e80] f5e80
[ 0.000000] init_memory_mapping: 0000000000000000-000000007fee0000
[ 0.000000] RAMDISK: 37483000 - 37ff0000
[ 0.000000] ACPI: RSDP 00000000000f5e00 00014 (v00 PTLTD )
[ 0.000000] ACPI: RSDT 000000007fee25a4 0003C (v01 PTLTD RSDT 06040000 LTP 00000000)
[ 0.000000] ACPI: FACP 000000007fee8e51 00074 (v01 INTEL 06040000 PTL 00000003)
[ 0.000000] ACPI: DSDT 000000007fee39cc 05485 (v01 INTEL GLENWOOD 06040000 MSFT 0100000E)
[ 0.000000] ACPI: FACS 000000007fee9fc0 00040
[ 0.000000] ACPI: MCFG 000000007fee8ec5 0003C (v01 PTLTD MCFG 06040000 LTP 00000000)
[ 0.000000] ACPI: APIC 000000007fee8f01 00074 (v01 PTLTD ? APIC 06040000 LTP 00000000)
[ 0.000000] ACPI: BOOT 000000007fee8f75 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001)
[ 0.000000] ACPI: ASF! 000000007fee8f9d 00063 (v32 CETP CETP 06040000 PTL 00000001)
[ 0.000000] ACPI: SSDT 000000007fee25e0 013EC (v01 PmRef CpuPm 00003000 INTL 20050228)
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007fee0000
[ 0.000000] Initmem setup node 0 0000000000000000-000000007fee0000
[ 0.000000] NODE_DATA [0000000001e441c0 - 0000000001e581bf]
[ 0.000000] bootmap [0000000001e59000 - 0000000001e68fdf] pages 10
[ 0.000000] (13/32 early reservations) ==> bootmem [0000000000 - 007fee0000]
[ 0.000000] #0 [0001000000 - 0001e43878] TEXT DATA BSS ==> [0001000000 - 0001e43878]
[ 0.000000] #1 [0037483000 - 0037ff0000] RAMDISK ==> [0037483000 - 0037ff0000]
[ 0.000000] #2 [0001e44000 - 0001e441ac] BRK ==> [0001e44000 - 0001e441ac]
[ 0.000000] #3 [00000f5e90 - 0000100000] BIOS reserved ==> [00000f5e90 - 0000100000]
[ 0.000000] #4 [00000f5e80 - 00000f5e90] MP-table mpf ==> [00000f5e80 - 00000f5e90]
[ 0.000000] #5 [000009e000 - 000009e4a1] BIOS reserved ==> [000009e000 - 000009e4a1]
[ 0.000000] #6 [000009e625 - 00000f5e80] BIOS reserved ==> [000009e625 - 00000f5e80]
[ 0.000000] #7 [000009e4a1 - 000009e625] MP-table mpc ==> [000009e4a1 - 000009e625]
[ 0.000000] #8 [0000010000 - 0000012000] TRAMPOLINE ==> [0000010000 - 0000012000]
[ 0.000000] #9 [0000012000 - 0000016000] ACPI WAKEUP ==> [0000012000 - 0000016000]
[ 0.000000] #10 [0000016000 - 0000018000] PGTABLE ==> [0000016000 - 0000018000]
[ 0.000000] #11 [0001e441c0 - 0001e581c0] NODE_DATA ==> [0001e441c0 - 0001e581c0]
[ 0.000000] #12 [0001e59000 - 0001e69000] BOOTMAP ==> [0001e59000 [ 1.382431] Freeing initrd memory: 11700k freed
[ 1.394058] Simple Boot Flag at 0x38 set to 0x1
[ 1.399591] audit: initializing netlink socket (disabled)
[ 1.405243] type=2000 audit(1302672510.404:1): initialized
[ 1.427027] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.436286] VFS: Disk quotas dquot_6.5.2
[ 1.440506] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.448016] msgmni has been set to 4007
[ 1.452698] alg: No test for stdrng (krng)
[ 1.457116] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.464916] io scheduler noop registered
[ 1.469077] io scheduler deadline registered
[ 1.473644] io scheduler cfq registered (default)
[ 1.479606] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.485552] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.492403] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 1.499422] pci-stub: invalid id string ""
[ 1.504029] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/PNP0C0C:00/input/input0
[ 1.513757] ACPI: Power Button [PWRB]
[ 1.517729] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 1.525533] ACPI: Power Button [PWRF]
[ 1.532942] ERST: Table is not found!
[ 1.537146] Non-volatile memory driver v1.3
[ 1.541561] Linux agpgart interface v0.103
[ 1.546005] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.796150] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
�[ 2.046149] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.052808] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 2.058792] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 2.066647] brd: module loaded
[ 2.070920] loop: module loaded
[ 2.074484] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 2.082032] scsi0 : ata_piix
[ 2.085274] scsi1 : ata_piix
[ 2.089902] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x30a0 irq 14
[ 2.097097] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x30a8 irq 15
[ 2.104343] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.111814] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 2.117599] scsi2 : ata_piix
[ 2.120812] scsi3 : ata_piix
[ 2.125585] ata3: SATA max UDMA/133 cmd 0x30e8 ctl 0x30dc bmdma 0x30b0 irq 19
[ 2.132955] ata4: SATA max UDMA/133 cmd 0x30e0 ctl 0x30d8 bmdma 0x30b8 irq 19
[ 2.140539] Fixed MDIO Bus: probed
[ 2.144276] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.151073] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.158473] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 2.164021] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 2.171848] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 2.178356] ehci_hcd 0000:00:1d.7: debug port 1
[ 2.187024] ehci_hcd 000[ 6.194957] generic-usb 0003:051D:0002.0001: hiddev96,hidraw0: USB HID v1.10 Device [American Power Conversion Smart-UPS 1500 FW:601.3.D USB FW:1.5] on usb-0000:00:1d.0-2/input0
[ 6.269922] dracut: Scanning devices sda2 for LVM logical volumes vg_drewserv/lv_root vg_drewserv/lv_swap
[ 6.325870] dracut: inactive '/dev/vg_drewserv/lv_root' [50.00 GiB] inherit
[ 6.333273] dracut: inactive '/dev/vg_drewserv/lv_home' [178.44 GiB] inherit
[ 6.340743] dracut: inactive '/dev/vg_drewserv/lv_swap' [3.94 GiB] inherit
[ 6.658963] EXT4-fs (dm-0): INFO: recovery required on readonly filesystem
[ 6.666270] EXT4-fs (dm-0): write access will be enabled during recovery
[ 6.786320] EXT4-fs (dm-0): recovery complete
[ 6.791601] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 6.859875] dracut: Mounted root filesystem /dev/mapper/vg_drewserv-lv_root
[ 6.987665] dracut: Loading SELinux policy
[ 7.230053] type=1404 audit(1302672517.979:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[ 8.341121] type=1403 audit(1302672519.090:3): policy loaded auid=4294967295 ses=4294967295
[ 8.984331] dracut: Switching root
[ 10.448852] udev[403]: starting version 161
[ 10.803998] intel_rng: FWH not detected
[ 10.866534] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 10.891884] EDAC MC: Ver: 2.1.0 Feb 7 2011
[ 10.904960] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4
[ 10.911461] e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
[ 10.919038] iTCO_vendor_support: vendor-support=0
[ 10.933753] e1000e 0000:0d:00.0: Disabling ASPM L1
[ 10.958846] e1000e 0000:0d:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 10.967333] e1000e 0000:0d:00.0: Disabling ASPM L0s
[ 10.979986] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 11.019016] e1000e 0000:0d:00.0: Warning: detected DSPD enabled in EEPROM
[ 11.073868] e1000e 0000:0d:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:30:48:56:a8:14
[ 11.082377] e1000e 0000:0d:00.0: eth0: Intel(R) PRO/1000 Network Connection
[ 11.089816] e1000e 0000:0d:00.0: eth0: MAC: 2, PHY: 2, PBA No: ffffff-0ff
[ 11.097339] e1000e 0000:0e:00.0: Disabling ASPM L1
[ 11.103579] e1000e 0000:0e:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 11.111251] e1000e 0000:0e:00.0: Disabling ASPM L0s
[ 11.118661] EDAC MC0: Giving out device to 'i3000_edac' 'i3000': DEV 0000:00:00.0
[ 11.127013] EDAC PCI0: Giving out device to module 'i3000_edac' controller 'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
[ 11.204562] e1000e 0000:0e:00.0: eth1: (PCI Express:2.5GB/s:Width x1) 00:30:48:56:a8:15
[ 11.213110] e1000e 0000:0e:00.0: eth1: Intel(R) PRO/1000 Network Connection
[ 11.220524] e1000e 0000:0e:00.0: eth1: MAC: 2, PHY: 2, PBA No: ffffff-0ff
[ 11.236770] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.06
[ 11.243348] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, TCOBASE=0x1060)
[ 11.255980] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 11.293708] leds_ss4200: no LED devices found
[ 11.421073] Linux video capture interface: v2.00
[ 11.986585] md: bind<sdd>
[ 11.991898] md: bind<sde>
[ 11.997302] md: bind<sdc>
[ 12.003366] md: bind<sdb>
[ 12.205094] async_tx: api initialized (async)
[ 12.214881] xor: automatically using best checksumming function: generic_sse
[ 12.226255] generic_sse: 4272.000 MB/sec
[ 12.230818] xor: using function: generic_sse (4272.000 MB/sec)
[ 12.350272] raid6: int64x1 1234 MB/s
[ 12.371279] raid6: int64x2 1308 MB/s
[ 12.392256] raid6: int64x4 1617 MB/s
[ 12.413297] raid6: int64x8 1078 MB/s
[ 12.434264] raid6: sse2x1 2007 MB/s
[ 12.455258] raid6: sse2x2 2855 MB/s
[ 12.476263] raid6: sse2x4 2894 MB/s
[ 12.480269] raid6: using algorithm sse2x4 (2894 MB/s)
[ 12.514503] md: raid6 personality registered for level 6
[ 12.520181] md: raid5 personality registered for level 5
[ 12.525889] md: raid4 personality registered for level 4
[ 12.531901] md/raid:md127: device sdb operational as raid disk 0
[ 12.538214] md/raid:md127: device sdc operational as raid disk 2
[ 12[ 17.809814] EXT4-fs (dm-0): re-mounted. Opts: (null)
[ 18.426160] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 18.496094] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[ 18.577891] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[ 19.995607] Adding 4128764k swap on /dev/mapper/vg_drewserv-lv_swap. Priority:-1 extents:1 across:4128764k
[ 20.850024] NET: Registered protocol family 10
[ 20.855168] lo: Disabled Privacy Extensions
[ 20.871263] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 21.570979] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 24.351239] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 24.368590] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 25.159089] RPC: Registered udp transport module.
[ 25.164125] RPC: Registered tcp transport module.
[ 25.169149] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 26.927637] ipmi message handler version 39.2
[ 26.946024] IPMI System Interface driver.
[ 26.950893] ipmi_si: probing via SMBIOS
[ 26.955050] ipmi_si: Adding SMBIOS-specified kcs state machine
[ 26.961392] ipmi_si: Trying SMBIOS-specified kcs state machine at i/o address 0xca8, slave address 0x20, irq 0
[ 27.417358] ipmi_si ipmi_si.0: Found new BMC (man_id: 0x0015d9, prod_id: 0x1134, dev_id: 0x20)
[ 27.426517] ipmi_si ipmi_si.0: IPMI kcs interface initialized
[ 27.442853] ipmi device interface
[ 27.549403] w83627hf: Found W83627HF chip at 0x290
[ 29.850494] Installing knfsd (copyright (C) 1996 [email protected]).
[ 29.954561] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 29.963014] NFSD: starting 90-second grace period
Fedora release 14 (Laughlin)
Kernel 2.6.35.11-83.fc14.x86_64 on an x86_64 (/dev/ttyS1)
drewserv.drewrents.readytoinvade.com login: