OctoPrint - Revision history

Drew at 08:36, 25 January 2018

2018-01-25T08:36:43Z

← Older revision		Revision as of 02:36, 25 January 2018
Line 3:		Line 3:
	= Setup OctoPrint =		= Setup OctoPrint =
	Add your user to the dialout group;		Add your user to the dialout group;
	<~~pre~~>		<syntaxhighlight lang=bash>
	$ usermod -a -G dialout drew		$ usermod -a -G dialout drew
	</~~pre~~>		</syntaxhighlight>

	== Build ==		== Build ==
	<~~pre~~>		<syntaxhighlight lang=bash>
	$ git clone https://github.com/foosel/OctoPrint.git		$ git clone https://github.com/foosel/OctoPrint.git
	$ cd OctoPrint		$ cd OctoPrint
	$ virtualenv venv		$ virtualenv venv
	$ ./venv/bin/python setup.py install		$ ./venv/bin/python setup.py install
	</~~pre~~>		</syntaxhighlight>

	== Run ==		== Run ==
	<~~pre~~>		<syntaxhighlight lang=bash>
	$ cd ~/OctoPrint		$ cd ~/OctoPrint
	$ venv/local/bin/octoprint		$ venv/local/bin/octoprint
	</~~pre~~>		</syntaxhighlight>

	== Browse ==		== Browse ==
Line 40:		Line 40:
	== Tune Extruder and Heatbed PID ==		== Tune Extruder and Heatbed PID ==
	Issue		Issue
	<~~pre~~>		<syntaxhighlight lang=bash>
	Recv: Error:Thermal Runaway, system stopped! Heater_ID:		Recv: Error:Thermal Runaway, system stopped! Heater_ID:
	Changing monitoring state from 'Printing' to 'Error: Thermal Runaway, system stopped! Heater_ID:		Changing monitoring state from 'Printing' to 'Error: Thermal Runaway, system stopped! Heater_ID:
Line 47:		Line 47:
	Changing monitoring state from 'Error: Thermal Runaway, system stopped! Heater_ID:		Changing monitoring state from 'Error: Thermal Runaway, system stopped! Heater_ID:
	' to 'Closed'		' to 'Closed'
	</~~pre~~>		</syntaxhighlight>

	Need to tune:		Need to tune:
	<~~pre~~>		<syntaxhighlight lang=bash>
	M105 # get extruder temp		M105 # get extruder temp
	M303 # tunes to 150C		M303 # tunes to 150C
Line 76:		Line 76:

	M500		M500
	</~~pre~~>		</syntaxhighlight>

	* https://www.lulzbot.com/fine-tune-your-marlin-pid-settings		* https://www.lulzbot.com/fine-tune-your-marlin-pid-settings
Line 82:		Line 82:
	= Setup mjpg-streamer =		= Setup mjpg-streamer =
	Add your user to the video group;		Add your user to the video group;
	<~~pre~~>		<syntaxhighlight lang=bash>
	$ usermod -a -G video drew		$ usermod -a -G video drew
	</~~pre~~>		</syntaxhighlight>

	== Build ==		== Build ==
	<~~pre~~>		<syntaxhighlight lang=bash>
	$ git clone https://github.com/jacksonliam/mjpg-streamer.git		$ git clone https://github.com/jacksonliam/mjpg-streamer.git
	$ cd mjpg-streamer-experimental		$ cd mjpg-streamer-experimental
	$ make		$ make
	</~~pre~~>		</syntaxhighlight>

	== Run ==		== Run ==
	<~~pre~~>		<syntaxhighlight lang=bash>
	$ cd ~/mjpg-streamer/mjpg-streamer-experimental/		$ cd ~/mjpg-streamer/mjpg-streamer-experimental/
	$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720 -d /dev/video0" -o "./output_http.so"		$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720 -d /dev/video0" -o "./output_http.so"
	$ uvcdynctrl -s "Focus, Auto" 1		$ uvcdynctrl -s "Focus, Auto" 1
	</~~pre~~>		</syntaxhighlight>

	* Reference		* Reference

Drew: /* Run */

2016-07-31T10:40:11Z

Run

← Older revision		Revision as of 04:40, 31 July 2016
Line 96:		Line 96:
	<pre>		<pre>
	$ cd ~/mjpg-streamer/mjpg-streamer-experimental/		$ cd ~/mjpg-streamer/mjpg-streamer-experimental/
	$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720" -o "./output_http.so"		$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720 -d /dev/video0" -o "./output_http.so"
	$ uvcdynctrl -s "Focus, Auto" 1		$ uvcdynctrl -s "Focus, Auto" 1
	</pre>		</pre>

Drew: /* Tune Extruder and Heatbed PID */

2016-07-25T06:01:02Z

Tune Extruder and Heatbed PID

← Older revision		Revision as of 00:01, 25 July 2016
Line 68:		Line 68:
	# Set PIDs for Extruder		# Set PIDs for Extruder
	M301 P12.33 I0.51 D74.50 # default  from Configuration.h		M301 P12.33 I0.51 D74.50 # default  from Configuration.h
	M301 P33.58 I1.75 D160.93 # tuned   for ~~the heated bed:~~		M301 P33.58 I1.75 D160.93 # tuned   for extruder

	# Set PID for Heatbed		# Set PID for Heatbed
	M304 P234.88 I42.79 D322.28 # default from Configuration.h		M304 P234.88 I42.79 D322.28 # default from Configuration.h
	M304 P519.74 I72.10 D936.70 #tuned		M304 P519.74 I72.10 D936.70 #tuned for heated bed
	Enter the following command to save the PID settings to EEPROM.		Enter the following command to save the PID settings to EEPROM.

Drew: /* Tune Extruder and Heatbed PID */

2016-07-24T07:08:40Z

Tune Extruder and Heatbed PID

← Older revision		Revision as of 01:08, 24 July 2016
Line 68:		Line 68:
	# Set PIDs for Extruder		# Set PIDs for Extruder
	M301 P12.33 I0.51 D74.50 # default  from Configuration.h		M301 P12.33 I0.51 D74.50 # default  from Configuration.h
	M301 ~~P35~~.02 I1.~~83 D167~~.82 # tuned   for the heated bed:		M301 P33.58 I1.75 D160.93 # tuned   for the heated bed:

	# Set PID for Heatbed		# Set PID for Heatbed

Drew: /* Tune Extruder and Heatbed PID */

2016-07-24T04:11:36Z

Tune Extruder and Heatbed PID

← Older revision		Revision as of 22:11, 23 July 2016
Line 39:		Line 39:

	== Tune Extruder and Heatbed PID ==		== Tune Extruder and Heatbed PID ==
	<pre> M105 # get extruder temp		Issue
			<pre>
			Recv: Error:Thermal Runaway, system stopped! Heater_ID:
			Changing monitoring state from 'Printing' to 'Error: Thermal Runaway, system stopped! Heater_ID:
			'
			Recv: 9
			Changing monitoring state from 'Error: Thermal Runaway, system stopped! Heater_ID:
			' to 'Closed'
			</pre>

			Need to tune:
			<pre>
			M105 # get extruder temp
	M303 # tunes to 150C		M303 # tunes to 150C
	M303 S180 # tunes to 180C		M303 S180 # tunes to 180C
	M303 S180 C10 # tunes to 180 for 10 times		M303 S180 C10 # tunes to 180 for 10 times
	M303 E-1 ~~S65~~ C10 # Use to tune the bed at 70C		M303 E-1 S70 C10 # Use to tune the bed at 70C
	Recv: Ku: 57.76 Tu: 38.50		Recv: Ku: 57.76 Tu: 38.50
	Recv: Classic PID		Recv: Classic PID
Line 54:		Line 66:
	Recv: Kd: 169.89		Recv: Kd: 169.89

			# Set PIDs for Extruder
			M301 P12.33 I0.51 D74.50 # default  from Configuration.h
			M301 P35.02 I1.83 D167.82 # tuned   for the heated bed:

			# Set PID for Heatbed
			M304 P234.88 I42.79 D322.28 # default from Configuration.h
			M304 P519.74 I72.10 D936.70 #tuned
			Enter the following command to save the PID settings to EEPROM.

	~~Enter that information into your Start Gcode in Slic3r using the following format, with your values substituted appropriately:~~		M500
	~~M301 P12.33 I0.51 D74.50 # default M301 P35.02 I1.83 D167.82 # tuned  or for the heated bed:~~
	~~M304 P234.88 I42.79 D322.28 #default~~
	~~M304 P114.54 I4.76 D689.66 #tuned~~
	~~Enter the following command to save the PID settings to EEPROM.  M500~~
	</pre>		</pre>

Drew at 04:04, 24 July 2016

2016-07-24T04:04:52Z

@@ Line 37: / Line 37: @@
 ** Printer Statistics
 ** StatusLine
 = Setup mjpg-streamer =

Drew: /* Run */

2016-07-23T12:23:08Z

Run

← Older revision		Revision as of 06:23, 23 July 2016
Line 57:		Line 57:
	$ uvcdynctrl -s "Focus, Auto" 1		$ uvcdynctrl -s "Focus, Auto" 1
	</pre>		</pre>

			* Reference
			** http://www.sphaero.org/blog:2012:0727_control_your_webcam_from_the_command_line

	== Browse ==		== Browse ==
	* http://192.168.1.121:8080/?action=stream		* http://192.168.1.121:8080/?action=stream
	* http://127.0.0.1:8080/?action=snapshot		* http://127.0.0.1:8080/?action=snapshot

Drew: /* Run */

2016-07-23T12:22:24Z

Run

← Older revision		Revision as of 06:22, 23 July 2016
Line 55:		Line 55:
	$ cd ~/mjpg-streamer/mjpg-streamer-experimental/		$ cd ~/mjpg-streamer/mjpg-streamer-experimental/
	$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720" -o "./output_http.so"		$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720" -o "./output_http.so"
			$ uvcdynctrl -s "Focus, Auto" 1
	</pre>		</pre>

Drew at 03:00, 17 July 2016

2016-07-17T03:00:19Z

← Older revision		Revision as of 21:00, 16 July 2016
Line 53:		Line 53:
	== Run ==		== Run ==
	<pre>		<pre>
			$ cd ~/mjpg-streamer/mjpg-streamer-experimental/
	$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720" -o "./output_http.so"		$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720" -o "./output_http.so"
	</pre>		</pre>

Drew at 02:59, 17 July 2016

2016-07-17T02:59:30Z

← Older revision		Revision as of 20:59, 16 July 2016
Line 1:		Line 1:
			Using a Raspberry Pi3 running Rasbian 8

	= Setup OctoPrint =		= Setup OctoPrint =
			Add your user to the dialout group;
			<pre>
			$ usermod -a -G dialout drew
			</pre>

	== Build ==		== Build ==
	<pre>		<pre>
Line 9:		Line 16:

	== Run ==		== Run ==
			<pre>
	$ cd ~/OctoPrint		$ cd ~/OctoPrint
	$ venv/local/bin/octoprint		$ venv/local/bin/octoprint
			</pre>

	== Browse ==		== Browse ==
Line 30:		Line 39:

	= Setup mjpg-streamer =		= Setup mjpg-streamer =
			Add your user to the video group;
			<pre>
			$ usermod -a -G video drew
			</pre>

	== Build ==		== Build ==
	<pre>		<pre>
Line 39:		Line 53:
	== Run ==		== Run ==
	<pre>		<pre>
	$ ~~sudo~~ ./mjpg_streamer -i "./input_uvc.so -r 1280x720" -o "./output_http.so"		$ ./mjpg_streamer -i "./input_uvc.so -r 1280x720" -o "./output_http.so"
	</pre>		</pre>