IPMI - Revision history

Drew: removed trailing spaces

2018-01-29T16:29:48Z

removed trailing spaces

Drew at 07:54, 25 January 2018

2018-01-25T07:54:05Z

← Older revision		Revision as of 01:54, 25 January 2018
Line 2:		Line 2:

	==SuperMicro ipmitool==		==SuperMicro ipmitool==
	<~~pre~~># service ipmi stop</~~pre~~>		<syntaxhighlight lang=bash>
			# service ipmi stop
			</syntaxhighlight>

	SuperMicro Configuration Tool Began to work		SuperMicro Configuration Tool Began to work
	<~~pre~~># ./ipmicfg-linux.x86_64.static -m		<syntaxhighlight lang=bash>
			# ./ipmicfg-linux.x86_64.static -m
	IP=192.168.1.21 MAC=00:30:48:56:A8:14		IP=192.168.1.21 MAC=00:30:48:56:A8:14
	# ./ipmicfg-linux.x86_64.static -k		# ./ipmicfg-linux.x86_64.static -k
Line 16:		Line 20:
	# ./ipmicfg-linux.x86_64.static -vlan		# ./ipmicfg-linux.x86_64.static -vlan
	VLAN feature is not supported by this firmware.		VLAN feature is not supported by this firmware.
	</~~pre~~>		</syntaxhighlight>

	*https://twiki.cern.ch/twiki/bin/view/FIOgroup/IpmiRefSolSetup		*https://twiki.cern.ch/twiki/bin/view/FIOgroup/IpmiRefSolSetup
	*http://wiki.alteeve.com/index.php/IPMI		*http://wiki.alteeve.com/index.php/IPMI


	==Common ipmitool commands==		==Common ipmitool commands==
	<~~pre~~># ipmitool -l open shell		<syntaxhighlight lang=bash>
			# ipmitool -l open shell
	# ipmitool -l open mc reset cold		# ipmitool -l open mc reset cold
	# ipmitool -I open lan print		# ipmitool -I open lan print
	# ipmitool -l open session info all</~~pre~~>		# ipmitool -l open session info all
			</syntaxhighlight>

	==Faster SOL==		==Faster SOL==
	* IPMIv2 only uses CTS/RTS (RTS/CTS);		* IPMIv2 only uses CTS/RTS (RTS/CTS);
	<~~pre~~># ipmitool -l open sol info 1		<syntaxhighlight lang=bash>
			# ipmitool -l open sol info 1

	sol set character-accumulate-level 1		sol set character-accumulate-level 1
Line 39:		Line 44:
	sol set non-volatile-bit-rate 115.2		sol set non-volatile-bit-rate 115.2
	sol set volatile-bit-rate 115.2		sol set volatile-bit-rate 115.2
	</~~pre~~>		</syntaxhighlight>

	==Remote IPMI shell==		==Remote IPMI shell==
	<~~pre~~># ipmitool -I lanplus -H 192.168.1.21 -U ADMIN shell		<syntaxhighlight lang=bash>
			# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN shell
	# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate		# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate
	# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN chassis power reset</~~pre~~>		# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN chassis power reset
			</syntaxhighlight>

	==rmcp_ping==		==rmcp_ping==
	<~~pre~~># rmcp_ping		<syntaxhighlight lang=bash>
	# rmcp_ping 192.168.1.21</~~pre~~>		# rmcp_ping
			# rmcp_ping 192.168.1.21
			</syntaxhighlight>


	==Fedora ??12?? grub.conf==		==Fedora ??12?? grub.conf==
	<~~pre~~># grub.conf generated by anaconda		<syntaxhighlight lang=bash>
			# grub.conf generated by anaconda
	#		#
	# Note that you do not have to rerun grub after making changes to this file		# Note that you do not have to rerun grub after making changes to this file
Line 80:		Line 89:
	title "My bios update"		title "My bios update"
	kernel /memdisk		kernel /memdisk
	initrd /fwdisk.img floppy</~~pre~~>		initrd /fwdisk.img floppy
			</syntaxhighlight>


	==Fedora 14 grub.conf==		==Fedora 14 grub.conf==
	*Set higher buadrate		*Set higher buadrate
	<~~pre~~># cat /etc/grub.conf
			<syntaxhighlight lang=bash>
			# cat /etc/grub.conf
	# grub.conf generated by anaconda		# grub.conf generated by anaconda
	#		#
Line 104:		Line 116:
	root (hd0,0)		root (hd0,0)
	kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM console=tty0 console=ttyS1,115200		kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM console=tty0 console=ttyS1,115200
	initrd /initramfs-2.6.35.11-83.fc14.x86_64.img</~~pre~~>		initrd /initramfs-2.6.35.11-83.fc14.x86_64.img
			</syntaxhighlight>

	==Fedora14 grub.conf orig==		==Fedora14 grub.conf orig==
	<~~pre~~>grub.conf		<syntaxhighlight lang=bash>
			grub.conf

	# grub.conf generated by anaconda		# grub.conf generated by anaconda
Line 127:		Line 141:
	root (hd0,0)		root (hd0,0)
	kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet console=ttyS1,19200		kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet console=ttyS1,19200
	initrd /initramfs-2.6.35.11-83.fc14.x86_64.img</~~pre~~>		initrd /initramfs-2.6.35.11-83.fc14.x86_64.img
			</syntaxhighlight>

	== Using the Serial BIOS ==		== Using the Serial BIOS ==
	*http://buttersideup.com/docs/howto/IPMI_on_Debian.html		*http://buttersideup.com/docs/howto/IPMI_on_Debian.html
	*The serial BIOS interface is a bit brain damaged in that it does not recognise the "F11", and "F12" key escape codes that most terminal programs send, instead you can send "Esc-!", and "Esc-@" (yes very logical, as long as the '@' key is normally typed using 'Shift-2' - as on US keyboards, not miles away from the '2' key, as on many non-US keyboards). These escapes from HP, and Dell serial BIOS' may or may not be useful:		*The serial BIOS interface is a bit brain damaged in that it does not recognise the "F11", and "F12" key escape codes that most terminal programs send, instead you can send "Esc-!", and "Esc-@" (yes very logical, as long as the '@' key is normally typed using 'Shift-2' - as on US keyboards, not miles away from the '2' key, as on many non-US keyboards). These escapes from HP, and Dell serial BIOS' may or may not be useful:
	<~~pre~~>		<syntaxhighlight lang=bash>
	Defined As F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12		Defined As F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
	Keyboard Entry <ESC>1 <ESC>2 <ESC>3 <ESC>4 <ESC>5 <ESC>6 <ESC>7 <ESC>8 <ESC>9 <ESC>0 <ESC>! <ESC>@		Keyboard Entry <ESC>1 <ESC>2 <ESC>3 <ESC>4 <ESC>5 <ESC>6 <ESC>7 <ESC>8 <ESC>9 <ESC>0 <ESC>! <ESC>@
Line 147:		Line 162:
	Use the <ESC><Ctrl><J> key sequence for <Ctrl><J>		Use the <ESC><Ctrl><J> key sequence for <Ctrl><J>

	Use the <ESC><X><X> key sequence for <Alt><x>, where x is any letter key, and X is the upper case of that key</~~pre~~>		Use the <ESC><X><X> key sequence for <Alt><x>, where x is any letter key, and X is the upper case of that key
			</syntaxhighlight>

	== Fedora 13 ==		== Fedora 13 ==
Line 154:		Line 169:

	==Sample Boot==		==Sample Boot==
	<~~pre~~>		<syntaxhighlight lang=bash>
	drew@drew-desktop:~$ ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate		drew@drew-desktop:~$ ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate
	Password:		Password:
Line 617:		Line 632:

	drewserv.drewrents.readytoinvade.com login:		drewserv.drewrents.readytoinvade.com login:
	</~~pre~~>		</syntaxhighlight>

Drew: /* Set higher baudrate on BMC */

2011-08-01T04:39:48Z

Set higher baudrate on BMC

← Older revision		Revision as of 22:39, 31 July 2011
Line 29:		Line 29:


	==~~Set higher baudrate on BMC~~==		==Faster SOL==
	* IPMIv2 only uses CTS/RTS (RTS/CTS);		* IPMIv2 only uses CTS/RTS (RTS/CTS);
	<pre># ipmitool -l open sol info 1		<pre># ipmitool -l open sol info 1
	~~# ipmitool -l open sol set help~~
	~~# ipmitool -l open sol set volatile-bit-rate 115.2 1~~
	~~# ipmitool -l open sol set non-volatile-bit-rate 115.2 1</pre>~~

			sol set character-accumulate-level 1
			sol set character-send-threshold 220
			sol set retry-count 0
			sol set retry-interval 0
			sol set non-volatile-bit-rate 115.2
			sol set volatile-bit-rate 115.2
			</pre>

	==Remote IPMI shell==		==Remote IPMI shell==

Drew at 06:52, 25 May 2011

2011-05-25T06:52:30Z

Show changes

Drew: /* Fedora14 grub.conf orig */

2011-04-14T02:11:13Z

Fedora14 grub.conf orig

← Older revision		Revision as of 20:11, 13 April 2011
Line 103:		Line 103:

	==Fedora14 grub.conf orig==		==Fedora14 grub.conf orig==
	grub.conf		<pre>grub.conf

	# grub.conf generated by anaconda		# grub.conf generated by anaconda
Line 123:		Line 123:
	root (hd0,0)		root (hd0,0)
	kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet console=ttyS1,19200		kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet console=ttyS1,19200
	initrd /initramfs-2.6.35.11-83.fc14.x86_64.img		initrd /initramfs-2.6.35.11-83.fc14.x86_64.img</pre>


	== Using the Serial BIOS ==		== Using the Serial BIOS ==

Drew at 02:10, 14 April 2011

2011-04-14T02:10:37Z

← Older revision		Revision as of 20:10, 13 April 2011
Line 101:		Line 101:
	kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM console=tty0 console=ttyS1,115200		kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM console=tty0 console=ttyS1,115200
	initrd /initramfs-2.6.35.11-83.fc14.x86_64.img</pre>		initrd /initramfs-2.6.35.11-83.fc14.x86_64.img</pre>

			==Fedora14 grub.conf orig==
			grub.conf

			# grub.conf generated by anaconda
			#
			# Note that you do not have to rerun grub after making changes to this file
			# NOTICE: You have a /boot partition. This means that
			# all kernel and initrd paths are relative to /boot/, eg.
			# root (hd0,0)
			# kernel /vmlinuz-version ro root=/dev/mapper/vg_drewserv-lv_root
			# initrd /initrd-[generic-]version.img
			#boot=/dev/sda
			serial --unit=1 --speed=19200
			terminal --timeout=5 serial console
			default=5
			timeout=5
			#splashimage=(hd0,0)/grub/splash.xpm.gz
			#hiddenmenu
			title Fedora (2.6.35.11-83.fc14.x86_64)
			root (hd0,0)
			kernel /vmlinuz-2.6.35.11-83.fc14.x86_64 ro root=/dev/mapper/vg_drewserv-lv_root rd_LVM_LV=vg_drewserv/lv_root rd_LVM_LV=vg_drewserv/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYTABLE=us rhgb quiet console=ttyS1,19200
			initrd /initramfs-2.6.35.11-83.fc14.x86_64.img

Drew at 06:19, 13 April 2011

2011-04-13T06:19:50Z

← Older revision		Revision as of 00:19, 13 April 2011
Line 41:		Line 41:
	# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate		# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN sol activate
	# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN chassis power reset</pre>		# ipmitool -I lanplus -H 192.168.1.21 -U ADMIN chassis power reset</pre>


			==rmcp_ping==
			<pre># rmcp_ping
			# rmcp_ping 192.168.1.21</pre>

Drew at 06:16, 13 April 2011

2011-04-13T06:16:24Z

← Older revision		Revision as of 00:16, 13 April 2011
Line 1:		Line 1:
			Useful IPMI commands on SuperMicro AOC-IPMI20 for Serial-Over-LAN Console

	==SuperMicro ipmitool==		==SuperMicro ipmitool==
	<pre># service ipmi stop</pre>		<pre># service ipmi stop</pre>

Drew at 06:13, 13 April 2011

2011-04-13T06:13:58Z

@@ Line 1: / Line 1: @@
-<pre>http://wiki.alteeve.com/index.php/IPMI
+==SuperMicro ipmitool==
+<pre># service ipmi stop</pre>
 SuperMicro Configuration Tool Began to work
+<pre># ./ipmicfg-linux.x86_64.static -m
 IP=192.168.1.21 MAC=00:30:48:56:A8:14
 # ./ipmicfg-linux.x86_64.static -k
 Net Mask=255.255.255.0
 # ./ipmicfg-linux.x86_64.static -dhcp
 DHCP is currently disabled.
 # ./ipmicfg-linux.x86_64.static -g
 IP=192.168.1.1
 # ./ipmicfg-linux.x86_64.static -ver
 Firmware Revision: 02.05
 # ./ipmicfg-linux.x86_64.static -vlan
 VLAN feature is not supported by this firmware.
-# service ipmi start
+*https://twiki.cern.ch/twiki/bin/view/FIOgroup/IpmiRefSolSetup
+*http://wiki.alteeve.com/index.php/IPMI
-<pre># ipmitool -l open shell</pre>
+==Common ipmitool commands==
-<pre># ipmitool -I open lan print</pre>
+==Set higher baudrate on BMC==
 * IPMIv2 only uses CTS/RTS (RTS/CTS);
 <pre># ipmitool -l open sol info 1
 # ipmitool -l open sol set help
@@ Line 47: / Line 34: @@
 # ipmitool -l open sol set non-volatile-bit-rate 115.2 1</pre>
-Start IPMI shell;
+==Remote IPMI shell==
-<pre># ipmitool -I lanplus -H 192.168.1.21 -U ADMIN shell</pre>
+<pre># ipmitool -I lanplus -H 192.168.1.21 -U ADMIN shell
-Use ipmitool to for serial over lan to host;
+==Fedora ??12?? grub.conf==
 <pre># grub.conf generated by anaconda
+#
@@ Line 90: / Line 71: @@
 	initrd /fwdisk.img floppy</pre>
-** Fedora 13 - Set console=ttyS1,19200n8 last for udev to automatically configure serial console on boot.

Drew at 05:58, 13 April 2011

2011-04-13T05:58:45Z

← Older revision		Revision as of 23:58, 12 April 2011
Line 32:		Line 32:
	https://twiki.cern.ch/twiki/bin/view/FIOgroup/IpmiRefSolSetup</pre>		https://twiki.cern.ch/twiki/bin/view/FIOgroup/IpmiRefSolSetup</pre>

			On localhost after installing;
			<pre># yum install OpenIPMI ipmitool</pre>

			<pre># ipmitool -l open shell</pre>

			<pre># ipmitool -l open mc reset cold</pre>

			<pre># ipmitool -I open lan print</pre>

			Set higher baudrate in BIOS, then BMC. * IPMIv2 only uses CTS/RTS (RTS/CTS);
			<pre># ipmitool -l open sol info 1
			# ipmitool -l open sol set help
			# ipmitool -l open sol set volatile-bit-rate 115.2 1
			# ipmitool -l open sol set non-volatile-bit-rate 115.2 1</pre>

			<pre># ipmitool -l open session info all</pre>

	Start IPMI shell;		Start IPMI shell;